日本原產ORC紫外線照度計、光量計、UV能量計,旗下包含UV-351
、UV-M03A(UV-M02、UV-M03已淘汰)、UV-M10(包含UV-M10-P、UV-M10-S)以及UV-M06H.
具體使用范圍見表:
最佳回答:
紫外線照度計1401是一種高質量的UV能量測量儀。其獨特設計的內置手把,在使用時更為方便。 融達紫外線照度計是用于測量不同光源的UV能量,尤其是用于印刷機器上。確保印刷及干燥之過程達到理想的質量控制。 能量計能測量的光譜范圍為 250-410納米,最佳感應 高峰光譜輸出為330納米。 當曝光循環時附加射入的光線 數量,相對的價值會計算在內。 由于光源不規律的放射分布,及不同制造商有不同的構造設計。以致在同一測量 條件下,可能出現不同的讀數。 使用方法: 1. 按下紫外線照度計之開關制“ON”,顯示屏上將顯示“0”。 2. 把紫外線照度計翻轉放在輸送帶上。(傳感器是安裝在儀器之背面,亦能抵受較高的溫度。) 3. 待儀器通過了輸送帶手,可從正面閱讀結果。 紫外線照度計顯示如:mJ/cm2 4. 在進行一個新的測量程序前,必須先把儀器關掉,然后再次開動。顯示屏上將重新調至“0”。 接著可依照2繼續操作。 注意事項: 1. 請避免搖動儀器。 2. 勿直視或非直視即通過折射/反射UV燈,保證身體的任何部位均不受UV燈直射。 技術數據: 光譜范圍: UV 250-410 nm(納米) 測量范圍: 0-5,000 mW/cm2(毫瓦特/平方厘米) 顯示范圍: 0-999,999 mJ/cm2(毫焦耳/平方厘米) 電 源: AAA電池 電 功 耗: 100μA 電池壽命: 正常操作使用一年 幾何尺寸: 140毫米直徑,13毫米高 凈 重 量: 約450克 環境溫度: 0至45度(攝氏℃) 瞬時溫度: 110(攝氏℃)溫度不可超過10秒。 調查校驗: 由于所有的電子原件,尤其是其燈光感應器,通常都會隨時間而老化,所以建議一年進行一次校驗。而且更換電池后,也應進行調查校驗。 According to 1401 meters UV is a high-quality UV energy meter. Its unique design of the built-in hand, more convenient in use. Melting of the UV meter according to the different light source is used to measure the UV energy, especially for the printing machine. To ensure that the process of printing and drying to achieve the ideal of quality control. Energy Meter to measure the spectral range of 250-410 nm, the best sensor peak output of 330 nanometer spectrum. When the exposure cycle the number of additional light into the relative value of the excluded. Irregular as a result of the radiation source distribution, and different manufacturers have different structural design. Result in the same measurement conditions, the readings may be different. Use: 1. Press UV system according to meters of the switch "ON", the display will show "0." 2. According to the ultraviolet light turned on the conveyor belt on the meter. (Sensor is installed in the back of equipment, can withstand a higher temperature.) 3. Through the conveyor belt to be hand equipment can be seen from the results of a positive reading. According to the UV meter shows such as: mJ/cm2 4. Conducting a new measurement procedure must first turn off the apparatus, and then start again. Will re-display to "0." Can then continue to operate in accordance with 2. Notes: 1. Please avoid shaking apparatus. 2. Do not open or open by refraction / reflection UV light to ensure that any part of the body are not subject to direct UV light. Technical Data: Spectral range: UV 250-410 nm (nanometer) range: 0-5,000 mW/cm2 (milliwatts / square cm) display range: 0-999,999 mJ/cm2 (mJ / square cm) Power: AAA battery Electric power consumption: 100μA battery life: the normal operation of the use of one-year geometry: 140 mm diameter, 13 mm high Net weight: 450 grams of about ambient temperature: 0-45 degrees (Celsius ℃) instantaneous temperature: 110 (Celsius ℃) temperature can not be more than 10 seconds. Check the survey: As all of the electronics components, especially its light sensor, usually with time of aging, it is proposed to conduct a check for one year. And replace the battery, the check should also be investigated.
最佳回答:
A正確,其實確切的說應該是基于對象的。
其他答案1:
用dw可以修改,記事本也可以修改。若果是你自己的網站當然保存在你的服務器上啊,上傳更新就好了,人家的服務器你是不知道密碼的?。?
8下列能設置下一個讀寫操作位置的是
A、Set語句B、Seek()函數
C、Seek語句D、Locate語句
9在下列循環中,語句“printx”被執行的次數是:()。PrivateSubForm_Click():x=7:While6<8:Printx,:Wend:EndSub(1分)
A、6次B、無數次
C、8次D、0次
10設菜單項名稱為M,若想運行時是該菜單項變?yōu)榛疑?失效),應使用語句為
A、M.Enabled=FalseB、M.Enabled=True
C、M.Visible=FalseD、M.Visible=True
11某控件在程序運行后,在窗體中沒有出現,是因為該控件的______屬性設置為False
A窗體B、Visible
C、EnabledD、AutoRedraw
12打開菜單編輯器的熱鍵為
A、Alt+MB、Ctrl+E
C、Alt+ED、Ctrl+M
13已知下列程序段:a=3:b=4:Printb>a,輸出的結果是
A、TrueB、False
C、4>3D、顯示出錯信息
14使用Windows98保存一新建的工程,其默認的路徑是______。(1分)
A、VBB、VB98
C、WindowsD、MyDocuments
15對于如下結構的循環:DoWhile條件:循環體:Loop,則下列正確的敘述為:
A、如果“條件”為常數0,則一次循環體也不執行;B、如果“條件”為常數-1,則一次循環體也不執行;
C、如果“條件”為常數-1,則只執行一次循環體;D、如果“條件”為常數0,則執行無限次循環體。
16對于如下結構的循環:Do:循環體:LoopUntil條件,則下列正確的敘述是
A如果“條件”為常數0,則只執行一次循環體;B如果“條件”為常數-1,則至少執行二次循環體;
C如果“條件”為常數-1,則只執行一次循環體;D如果“條件”為常數0,則一次循環體也不執行。
17變量未賦值時,字符串變量的值為
A、OB、空串""
C、NullD、沒任何值
18下列正確的定義語句為
A、Subaa(n)AsIntegerB、Subaa(ByVala())
C、Functionaa(Byvalx)D、Functionaa(x)
19假如列表框(Listl)有六個數據項,那么把數據項“hello”添加到列表框的最后,應使用的語句為
A、Listl.AddItem5,“hello”B、Listl.AddItem“hello”,Listl.ListCount-1
C、Listl.AddItem“hello”,5D、Listl.AddItem“hello”,Listl.ListCount
20如果列表框(Listl)中沒有被選定的項目,則執行Listl.RemoveItemListl.ListIndex語句的結果是
A移去第一項b移去最后一項
C移去最后加入列表的一項d以上都不對” open=”yes”]
最佳回答:
其實這些都可以在VB里進行測試.我也得到了練習.謝謝
1 A
2 D
3 B
4 B
5 A
6 D
7 A
8 C
9 D
10 A
11 B
12 B
13 A
14 B
15 A
16 C
17 B
18 題目不完整
19 D
20 D
最佳回答:
D
其他答案1:
D.面向?qū)ο蟮某绦蛟O(shè)計語言
其他答案2:
VB中按鈕,文本框等都是對象。
系統是面向?qū)ο缶幊痰摹?
最佳回答:
答案是A。B是網頁設計程序,C是文字識別程序,D是看圖軟件。只有A是編程語言。
其他答案1:
那肯定是A